[产品] SYK3350型新型多色印刷开槽机

详细说明：

    该机可组成双、三、四、五色印刷开槽机，能同时完成印刷、分切、压痕、开槽、切角工序。
    ● 印刷部功能：
    ◆ 印刷部传动部分采用大螺旋角斜齿传动，在降低噪音的情况下，提高了齿轮的强度和传动的平稳性。而且传动齿轮采用45#锻造件，且调质淬火处理，增强了耐用性和寿命，使套色精度有了很长时间的保证。
    ◆ 印刷部传动部分，进纸采用十字滑块传动。压印辊及接纸辊齿轮采用卫星式摇板传动机构，即在压印和接纸间隙大小调整的过程中齿轮之间始终正常啮合，不增大齿顶和齿侧间隙，使套印尤其多色套印更加准确，并使齿轮间应损降至**低。
    ◆ 向位部分采用360度停机和不停机调整。可在工作过程和停机状态下调整，并有刻度显示，但与现行向位调整不同的是：在大齿轮传动接合部采用2个轴承支撑接合，避免了现行齿轮与调整内齿圈套式结合所产生的端面跳动和易锁死现象和使用寿命低等缺陷。而且调整部分采用行星加蜗轮蜗杆传动方式，增大了传动力矩和调整的方便准确性。
    ● 着墨部功能：
    ◆ 着墨部分匀墨采用胶辊，网辊着墨，而且根据用户印刷情况的多样性对线速比进行了优化，加粗了网辊和胶辊的辊径，使转速比更加合理和增加了运转中匀墨的平稳性和轴的刚性。传动亦做了改进，由原来的间接网辊传动改为直接传动。在胶辊间隙任意调整的情况下，网辊齿轮之间无间隙，使网辊与版辊线速始终保持**致，使积累和着墨重影以及清晰度有了很大的改观。
    ● 开槽部功能：
    ◆ 开槽部采用先开槽后压线，方便调整，且开槽刀盘移动齿轮为内装式，使操作更方便。

Brief Introduction:
    Brief introduction to the performance:
This machine can constitute the double-color, 3-color,4-color and 5-color printing & slotting machines which can simultaneously accomplish the process of printing, separate cutting, creasing, slotting and corner cutting.
    ● Function of the printing part:
    ◆ The drive part of the printing part adopts the big screw and bevel gear drive which increases the strength of the gears and the driving stability under the circumstance of lowering the noise. With 45# forging-works and quench treatment the drive gears have increased the durability and life, and greatly guaranteed the precision of chromatographing.
    ◆ The paper-feeding of the drive part of the printing part adopts cross sliding drive. The gears of the print pressing roller and the paper-catching roller adopt the planetary rocker-plate drive device. The gears are normally meshed from beginning to end while the space between the print pressing and the paper catching is adjusted, which does not enlarge the space between the gear-top and gear-side, make the color process (esp. the multi-color process) more accurate and lower the wear between the gears to the minimum.
    ◆ The phase part adopts 360?adjusting while stop working or during working. The scale will display this two kinds of adjustment which are different from the current phase adjusting, i. e. the driving and jointing part of the large gear adopts 2 bearings to support and joint, which has prevented the sleeve joint of the current gear and the inside-gear-circle from the ends-and-surface moving up and down, easy to lock, short service life and other defects. And the adjusting part adopts the planetary, worm wheel and worm driving method, which has greatly enlarged the drive moment and raised the accuracy of adjusting.
    ● Function of inking part:
    ◆ The ink distributing of the inking part adopts the rubber roller and the anilox roller inking. The linear velocity has been improved according to the variety of the printing situations of the clients. The thickness of the roller diameter of the anilox roller and the rubber roller has been increased which has made the rotating speed rate more reasonable, and added the stability of ink distributing during operation and the rigidity of the axle. The drive has also been improved, i.e. changed to direct drive from the original indirect anilox roller drive. Under the circumstance of the space between the anilox rollers can be free adjusted, there is no space between the gears of the anilox rollers, which makes the linear velocity of the anilox roller and the plate roller keeping consistent from beginning to end, and makes the repeated trace of ink accumulating, inking and the clarity greatly improved.
    ● Function of slotting part:
    ◆ The slotting part adopts the method of the first slotting and then creasing which is convenient to adjust. The moving gear of the knife disk of slotting is inside-installed-type which is convenient to operate.