模切红宝书系列教材(一)
模切技术论坛 模切网微信公众平台
欢迎 游客 , 注册 | 登录 | 会员 | 界面 | 简洁版本 | 在线 | 帮助  
模切论坛

发表新主题 回复该主题
本主题被查看175608次, 共34个帖子
标题: 国外模具厂模具标准
模切会员
UID: 91
来自:
精华: 0
积分: 81
帖子: 71
注册: 2007/4/12 16:37:00
状态: 离线
威望: 10.00
金钱: 13.40 元
 
2007/9/11 22:35:00
回复:国外模具厂模具标准
III.  Die  Classifications    模具**别
A. All dies will be constructed for inter-changeability of perishable die blocks, punches, retainers, die buttons, and pilots.
模具需保证易坏的镶快、冲头、固定器、引导冲组装的易换性。
B.  Die material requirements:  模具材质要求
     Die Component Description模具组件名称    Die Material Type材质种类
         Die steel       模板                D2 or better
         Filler steel            导料板                   HRS/CRS
         Buttons       镶件                M-2
         Pilots                       引导冲            M-2
         Punches       冲头                M-2
         Buttons & punch retainers  镶件及冲头固定装置          A2, 6150,
           -                        4140 steel - hardened
         Pressure pads        压料垫板              6150 or 4140 steel -hardened                                 (See p.17, S-16)
         Stripper windows      脱料板快拆窗口                  6150, 4140 or 0-1 steel hardened
           -                        (See p. 17, S-16)
         Form steel        成型            D2 or better

    In any application where Su-dan is stamping a high strength or high carbon material the use of CPM-4, CPM10V, and CRU-Wear material with a surface coating should be discussed.
在Su-dan冲压高强度及高碳材质的地方,如应用……表面强化需讨论

IV.  Metal Stamping Dies - General Requirements:  五金模具——**般要求
             A.  Die design and construction data sheet: 模具设计与组立数据表
1.  The Su-dan Engineer shall complete and submit data sheet with each die proposal request  (Including shut height, feed levels,parallels, etc.).
Su-dan工程师应填写及提供每**套模具方案要求的资料表(包括闭模高度、送料高度、垫脚等)
2.  Data sheet will be updated at final die design review, including the Project Engineer and the vendor’s recommendations, which will become part of the general die specifications.
资料表在*终模具审核时应该更新,项目工程师及供应商的建议都将成为普通模具规范的**部分。
B.  Die design approval:    模具设计审核
1.  A strip layout is required on all parts before formal design is started.  The strip layout is to reflect the stock width, the progression, and the tonnage required to produce the stamping. Strip layouts should be developed so that scrap pieces are not left in the die.
在正式设计之前必须提供料带排布,料带包含料带宽,步距,冲床吨位,料带应保证废料不停留在模具上.
2.  To conserve material, the edge of the part may be the edge of the coil material wherever the part design will permit.  Using edge of coil material as part entity will require written approval from the Tool Engineer.
为了节约料,产品边可使用材料边,如使用卷料边,需要模具工程师的书面批准!
         3.  The strip should be developed to maintain maximum strip strength for the greatest possible distance through the die.
           料带应该强化到*大强度以通过*大的模板距离
4.  A die should be designed to minimize any strip distortion which would tend to change the distance between pilot holes (alter the progression).
模具设计应保证*少的任何改变料带步距的料带扭曲.
5.  All die designs will include part number, stamped on the part if indicated on the part print and a Su-Dan ID. stamp if required.
如果产品图面指示或Su-Dan 有号码要求所有模具设计应包含部件号码并刻印在零件上.
6.  All die designs that involve both single and/or double progressive dies that produce the following:
                                在**出**及**出二的连续模设计中,产品应该符合以下标准:
a.  A right and left hand part, if symetrically opposite,  will be equipped with either “R” and “L
        identification on each part. 
                                    左右对称相反的零件,必须在每个零件上刻上字符 L 及 R
b.  If parts are not symmetrically opposite a 1/8” letter “T” identification should be used on one of the parts.
    如果左右不是对称相反的零件,在其中的**个零件必须加上1/8” 高的T加以区别。       
c.  In some cases, a part number destination will be an dated by the part print or requested by the      Project Manager.
    在有些案例中,根据图面或项目工程师的要求,零件料号将有**个日期区别
d.  Julian date stamps (interchangable) will be required on all safety parts.
7.    All die capable of producing multiple level designs from that die, must be equipped with a provision for interchangable part identification to distinguish all variations  capable of being produced from that die.  Consult      with Project  Manager for specific identification.
    在共用模具设计中,必须预先对快换入子提供**个可区别的方法,可以与制定标准的项目经理商量
8.    All die drawing numbers plus special die drawings will be supplied at preliminary review.
                              在初**设计中所有模具图纸必须完全提供。
9.    Provision for loading and unloading of raw materials for all dies, as well as part ejection and scrap removal will be covered during the die design.
               在所有模具设计中,必须提供未加工和已加工的工序图,以及产品顶出及废料脱落方式。
10.  Designs will avoid excessive use of lubrication to produce stampings。
                           在模具设计中应该避免过多的使用润滑油去制造产品。
11.  If stock does not start against a pitch notch (positive stop) a start mark for first hit will be necessary.
                 如果条料没有步距开口槽(正**停止)送进,首次冲压条料送到位置的标记是有必要的。
12.    Full scale preliminary drawings must be reviewed on site between Project Manager and Vendor.  Drawings must be approved by Project Manager prior to the start of construction.
在项目经理与供应商规定的时间必须对全尺寸的初**设计进行审核,在组装开始之前图面必须得到项目经理的承认。
13.    The die supplier will furnish in writing the developed blank size along with the preliminary tool drawing(s).
在提交初**设计的同时供应商应提供下料尺寸。
14.    All die designs are to be originated and dimensioned using inch standards.
所有的模具设计用英制原点标注。
15.    Dies are to be designed so they can be maintained in the press using inserts in forms and cut off sections.  All forming inserts must be adjustable to accommodate stock thickness variance.
设计时应考虑使用成形入子及刀口入子,所有的成形入子应该可以根据料厚的变化可以调整。
16.    Wear points of the die sections must be inserted for economical maintenance, replacement cost, and adjustability for stock variance.
所有模具入子耐磨的地方必须使用镶嵌以方便经济的维修,置换以及根据料厚的变化调整能力。
17.    Die should contain a minimum of one idle station to accommodate future design considerations.  i.e. restrike, cam  pierce, etc.
摸具应至少包含**个空站以适应未来的设计变更,回整,凸轮,冲孔等。
18.    The position of the ball seat and key flats must be noted on stock list when not in standard position on oblong and rectangular punches and buttons.
当椭圆形,矩形的冲头及入子没有在标准的位置时,球锁的位置及扁平键应该标在料表清单上。
19.    Die designs should include the provisions for sensors.  A minimum of  two sensors-See Section K1.
模具设计中至少使用两种感应器。
         20.In addition the die design drawing will show:  此外,模具设计图面应显示:
            a.  Strip layout (full scale if possible).                  料带 (只要可能的话必须全尺寸)
            b.  Plan view (top and bottom section assembly). 平面图 (上下部分的剖视组装图)
            c.  Sectional views (right and left and/or front and back as required to show construction).
                                    剖视图 (前后左右的反映结构的视图)
            d.  Cross-sectional views (for timing, punch length, and travel of springs).
                                    横断面视图 (剪边,冲头长度以及弹簧的行程)
        e.  Detail drawing(s) of all perishable trim and form sections with material identified.  Detail drawing(s) will be on 8.5” x 11” paper with Su-dan title block provided in a binder and/or Cad data.
                                    所有的易磨损的冲头以及成形块必须用细部图表示并注明材料,细部图将使用Su-dan 用文件夹或Cad提供的8.5” x 11”标题框。
20.    Die progress reports are to be submitted twice a month to the Su-dan Project Manager.
每个月应向Su-dan项目工程师提交两次的模具进度报告。
21.    Paper is to be 34” x 22” with the standard Su-dan title block.
图纸应为34” x 22”大并使用Su-dan的标准图框
 
 

本主题被查看175608次, 共34个帖子



标题: 国外模具厂模具标准
可以在线看也可以下载到本地看,下载解压缩后可看到是**个word文档: [attach]207[/     (moqie 发表于 2007/9/11 22:34:00)
   III. Die Classifications 模具**别 A. All dies w     (moqie 发表于 2007/9/11 22:35:00)
   G.Die performance: 模具性能 1. All dies to be     (moqie 发表于 2007/9/11 22:35:00)
   15. Flattening and restrike sections are to be pro     (moqie 发表于 2007/9/11 22:36:00)
   I. Maintenance requirements: 维修要求: 1. Die sec     (moqie 发表于 2007/9/11 22:36:00)
   f. Welding on any portion of the draw rings must b     (moqie 发表于 2007/9/11 22:36:00)
   15. Clearance between punches and cutting sections     (moqie 发表于 2007/9/11 22:37:00)
   6.All strippers will be postively retained using d     (moqie 发表于 2007/9/11 22:37:00)
   9. All reference materials for the system inclu     (moqie 发表于 2007/9/11 22:38:00)
   以下信息应用至少.25”高字体压印在面对操作者的下模前方: 1. Die number.     (moqie 发表于 2007/9/11 22:38:00)
   也顶**下     (昆山圆刀 发表于 2007/9/12 9:38:00)
   :) :) :$     (模切好风景无限 发表于 2007/10/12 12:38:00)
   顶,楼主太强了     (Jethro 发表于 2007/12/25 22:19:00)
   :) :) :) :D :D :D     (膜切工程老兵 发表于 2007/12/26 22:06:00)
   五金模具标准!!!:'( 哪位大虾有**版的模切标准啊????????     (xiaospring021 发表于 2007/12/27 14:09:00)
   :) :) :)     (mutu 发表于 2008/1/2 19:58:00)
   太多了,没看明白:'(     (sxziyun 发表于 2008/1/4 17:10:00)
   感谢分享!但附件无法下载~~~~~     (laobendan 发表于 2008/1/9 11:46:00)
   太详细了,谢谢:D     (hrong7908 发表于 2008/2/2 10:06:00)
   :L :L :L :L :L :L     (Nicolas 发表于 2008/3/14 3:53:00)
   perfect document!!     (dalianair 发表于 2008/4/17 9:11:00)
   看不明白,不过还是要顶下楼竹     (zhangwenhua3083 发表于 2008/5/23 20:26:00)
   好多!看得头晕晕的!:)     (天之云 发表于 2008/6/25 14:30:00)
   hao zi liao     (song123456 发表于 2008/11/11 19:09:00)
   楼主,强阿,值得表表扬。     (jimlima 发表于 2009/9/22 22:44:00)
   先顶**下 再拿资料     (lgtqwww 发表于 2009/9/29 13:39:00)
   强悍~!     (lcg 发表于 2009/10/9 11:46:00)
   谢谢楼主,有意思的     (JACK_YJM 发表于 2010/2/8 13:04:00)
   谢谢!LZ ! 您辛苦了!~     (rickwang 发表于 2010/4/19 17:14:00)
   :D :D :D 顶**下     (growth 发表于 2010/6/24 9:50:00)
   受用了,谢谢楼主     (Kovi 发表于 2010/11/18 13:43:00)
   太好了,牛人,有空将之转成检查表形式,再和亲们分享!     (jerry_200076 发表于 2011/2/10 12:49:00)
   support     (JACK_YJM 发表于 2011/5/8 9:56:00)





现在的时间是 2024-06-16 14:49:19

© 模切网版权所有 不得转载 粤ICP备07017347号